GREAT PLAINS YP2425 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 166

background image

YP2425 and YP2425F

Table of Contents

Operating Instructions

35

2016-11-16

Table of Contents

401-406M

Transport Checklist



If heading to the field, before departing, ensure that
opener depth, seed rate and fertilizer rate have been
determined, or that the necessary data is with you.



Plan the route. If towing a cart hitched to the planter,
plan the route so that no reverse movements will be
necessary. Avoid steep hills. Keep Clearances in
mind. Folded, your YP24 may be nearly 15 feet
(4.6 m) wide and 13 feet (4 m) high.



Close slide gates on hoppers or seed boxes.



Hitch.
Make both electrical and hydraulic connections. See
“

Hitching Tractor to Planter

” on page 15.



If markers are unfolded, fold them.
See “

Folding the Markers

” on page 40.



Raise planter.
See “

Raising/Lowering Planter



Install lock-up channels on lift cylinders.
See “

Lift Cylinder Lock-Up

” on page 33.



If planter wings are unfolded, fold them.
See “

Folding the YP24

” on page 31. Make sure

wing locks are engaged.



Make sure caster locks are disengaged on newer
planters so equipped. See “

Folding the YP24



3-point hitch:
Lower hitch fully to ensure wings remain locked.
Hydraulic hitch:
Confirm CFM set to Hitch and hitch circuit in Float.



Always have lights on for highway operation.



Comply with all federal, state and local safety laws
when traveling on public roads.



Travel with caution.

Do not exceed 20 mph when driving straight.

Do not exceed 13 mph in turns.

Steering

Never exceed 13 mph (22 kph) in turns. The YP24 is
extremely heavy, and can cause “over-steer” with most
tractors. The leading gauge wheels, rear-most transport
wheels, PFC tank cart lead wheel and SML tank cart
trailing wheels fully caster, and provide no resistance to
side sway by the planter or cart.

Never exceed 3 mph (5 kph) in reverse.

Never back up with the planter lowered or with a fertilizer tank
hitched to the planter.

«
...
37
38
39
40
41
...
»

Содержание YP2425







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP2425

Бренд: Jacobsen Страницы: 10

Rotary Cutters RCR1860

Бренд: Land Pride Страницы: 34

Бренд: Flymo Страницы: 10

Бренд: Viking Страницы: 36

Бренд: Murray Страницы: 52

2261ADC Articulator

Бренд: Lastec Страницы: 67

TECHline NEXTTECH L X4

Бренд: ZCS Страницы: 42

Бренд: Stiga Страницы: 2

Бренд: Murray Страницы: 52

Бренд: LawnMaster Страницы: 81

Бренд: Simplicity Страницы: 80

Бренд: LawnMaster Страницы: 32

Бренд: LawnMaster Страницы: 40

Бренд: LawnMaster Страницы: 40

Бренд: LawnMaster Страницы: 26

Бренд: Toro Страницы: 24

Бренд: Worx Страницы: 196

Бренд: TIGA Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды