GREAT PLAINS YP2425 Скачать руководство пользователя страница 100

Страница: 100 / 166

2016-11-16

Table of Contents

Index

401-406M

YP2425 and YP2425F

Table of Contents

Index

Maintenance and Lubrication

Cleaning Out Air System

Shut off sliding door at bottom of seed boxes or bulk
hoppers.

Place a pan or tarp under the manifold to catch the
seed.

Open manifold door to empty seed from the
manifold.

Shut doors under manifolds.

Turn on the fan and let it run.

Refer to Figure 131

Note:

30 inch single-row planters do not have Y-tubes.

Go meter to meter, open clean-out door and blow
out seed.

Shut off the gates at all of the Y-tubes.

Start at one end of planter and open the meter clean
out door for the end row-unit. Place a bucket under
the meter to catch the seed.

Open the Y-tube gate feeding that meter. Let the air
blow seed out of the meter. Keep the meter open for
a couple of minutes after the seed stops blowing out.

Close the Y-tube gate feeding that meter. Close the
meter clean out door.

10. Repeat procedure on the next meter in line.

Continue with this procedure until you have reached
the opposite end of the planter.

Meter Drive Chain

Refer to Figure 132

Remove the seed meter and check the chain and
sprocket for wear. See “

Meter Removal

” on page 76 for

more information.

Figure 131

Y-Tube Shut-Off

22843

Figure 132

Meter Drive Chain

21917

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды