GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 81

Страница: 81 / 172

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

2019-03-11

Table of Contents

Index

407-502M

Stopping Application

Plan your stops. A safe stop requires depleting the

anhydrous, from the nurse tank withdrawal valve to the

knives or tines.
a. What is the wind direction?
b. Suspend application per “

Suspending Application

”

on page 76.

c. Put on your chemical gloves.

Be wearing your goggles.

d. Carefully approach the nurse tank from up-wind.

Expect some ammonia odor, but if it is extremely

strong, there may be an above-ground release in

progress due to malfunction or part failure. If so,

remain clear until the release subsides.

e. When safe to do so, shut off the nurse tank

withdrawal valve

Re-enter the tractor cab.

g. Turn MASTER switch ON.
h. Resume field application until reported rate begins to

fall. Increase rate to maximum (to fully open Control

Valve

Continue field application until both cooler and

divider pressure gauges read zero.

Facing into the wind, raise the applicator and stop.

k. Set the MASTER switch to OFF.
l.

Wait at least 1 minute for row line vapor to dissipate.

m. Turn so that the wind is directly from the right.
n. Open all bleed valves. Standing up-wind of each,

and making sure orifices point away from you, slowly

open bleed valves at:

• nurse tank hose inlet end

• nurse tank hose outlet end

• breakaway valve (

, whichever is safer)

• cooler temperature gauge

o. Close all remaining operating valves:

• nurse tank hose inlet end

• nurse tank hose outlet end

• emergency shut-off valve

p. Wait at least one hour before moving applicator to

any spot near unprotected people or livestock. It will

continue to out-gas ammonia vapor for some time.

Ball Valves: Trapped NH

Hazard:

Avoid routinely closing ball valves (other than the nurse tank

withdrawal valve) with liquid NH

in the lines. Fluid is

trapped in the line above the valve, may trigger relief valves,

and can get trapped inside the valve ball unless it has a bleed

port (not yet common on nurse tank hoses).

See “Avoid Line

Traps

” on page 113 and “

Avoid Ball Traps

” on page 114.

A typical ball valve can trap enough NH

to make a room the

size of a two-care garage uninhabitable (concentrations above

IDLH in moments). When the ball valve is later opened, while

warm, the NH

is expelled at high pressure. If the line is

pointed at your face, you could receive a fatal exposure.

A65

A61

A60

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды