GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 101

Страница: 101 / 172

NP30A or NP40A

Table of Contents

Index

Adjustments

2019-03-11

Table of Contents

Index

407-502M

Spring Knife Release Depth

Refer to Figure 75

Knife release depth

is set by tool bar height above

the ground. Control of height depends on hitch type.
Pull-Type applicators have an adjustable hydraulic

down-stop for controlling tool bar height (page 85).
2-Point and 3-Point applicators rely on tractor hitch

height for center tool bar height. Wing tool bar height is

set to match the center using a crank-assisted manual

adjustment (page 86).
Design shoe operating depth is 4 to 6 in (10 to 15 cm).

Operation at and below 8 in (20 cm) is not

recommended, as a high rate of bolt shears (page 100)

is likely.

Spring Knife Depth Reference Information

Overall height of the tool bar base to knife shoe base is:

30.25 in (76.8 cm)

Liquid NH

is released from the tube at:

in (19 mm) above the shoe base.

For a precise release depth, subtract this amount from

the total knife depth .

Chemical Hazard:

Adjust height dry. Make this adjustment before charging the
metering system with anhydrous ammonia, or after thoroughly

discharging the system. With the knives or tines out of the

ground, there could otherwise be releases of ammonia at
dangerous concentrations.

Figure 75

Spring Knife Application Depth

36006

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды