GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 63

Страница: 63 / 172

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

2019-03-11

Table of Contents

Index

407-502M

Unfolding and Folding

Nutri-Pro

applicators differ in locks and operational

steps:

• Pull-Type applicators have a simple dedicated fold

system with no wing locks. See “

Unfolding and

Folding Pull-Type

” below.

• 3-Point applicators have wing locks requiring reset

prior to fold. See “

Unfolding and Folding 3-Point

”

on page 60.

• 2-Point applicators have a lift-assist that usually

requires reconfiguring just prior to unfold and fold.

Additional steps vary with configurations:

On 3-section, and 2012- 5-section, wing locks

require reset prior to fold. See “

Unfolding and

Folding 3-Section and 2012- 2-Point 5-Section

”

on page 61.

2013+ 5-section applicator require a switch setting

change. See “

Unfolding and Folding 2013+

2-Point 5-Section

” on page 63

Unfolding and Folding Pull-Type

The pull-type applicator has no particular restrictions on

unfolding or folding on or off the field. As long as the lift

circuit is fully raised, knife/tine strike is not an issue.

Unfolding Pull-Type (At Field)

These instructions presume the applicator has just

completed transport, and is being unfolded for field use.
1. Point the applicator into the wind.
2. Close the weight-transfer shut-off valve (page 50).
3. Extend the fold cylinders to unfold.
4. Set control to Float when wing front caster wheels

contact the ground.

5. Extend the lift circuit (page 51) to raise the applicator

fully.

6. Remove and store the transport locks at center

section and lift-assist cylinders (page 45). If wing lift

cylinder lock channels were installed. Remove them

and re-engage hydraulic depth stop (page 47).

7. Open the weight-transfer shut-off valve.
8. If lined up at field, retract the lift circuit to lower the

applicator to height set by the hydraulic depth stop

(page 85).

9. Set the lift circuit to Float.

Folding Pull-Type

These instructions presume the applicator has just

completed application, and is being folded for transport

or parking.
1. Stop NH

flow (page 77), which includes heading

into the wind, and raising the applicator out of the

ground.

2. Close the weight-transfer shut-off valve (page 50).
3. Wait for the lines to discharge.
4. When the applicator is safe to approach, re-extend

the lift circuit to assure that it is fully raised.

5. Install lock channels at the lift-assist and center

section lift cylinders (page 45).

6. Retract the fold cylinders to fold the wings.
7. Stop, circuit in Neutral, when both wings are on the

transport rest.

8. Leave the fold circuit in Neutral for transport, or set

the to Float for unhitching.

Loop Ammonia Exposure Hazard:

Allow no one down-wind of the applicator when folding and

unfolding. Delivery tubing loops may contain liquid NH

that

can drain out of knives or tines during wing movement. This

liquid can remain in the loops long after application has

ended.

After parking overnight or longer, any liquid present may be

highly caustic ammonium hydroxide (concentrated NH

OH, a

solution of NH

and atmospheric moisture) rather than pure

. Assume any liquid in loops is extremely hazardous.

Take full NH

field precautions.

Ammonia Exposure Hazard:

Face applicator up-wind or clear the delivery lines (page 116)
before unfolding or folding. Fluid in delivery line loops,

whether pure NH

or concentrated NH

OH, is likely to move

from the loops and drip out at the knives or tines.

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды