manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 59

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

55

2019-03-11

Table of Contents

Index

407-502M

Raise/Lower 2013+ 5-Section

These instructions apply to 2013 and later 5-section

applicators. For 3-section applicator, and 2012- 5-section

applicators, see page 53.

Raise For Transport (Folded) 5-Section 2013+

These steps presume an applicator parked or stored

folded, already raised, but on lift-assist locks and parking

stands. No use of the applicator hydraulics is required.
1. Verify that lock channels are installed on the

lift-assist cylinders (page 45).

2. Verify that wing lock pins are installed on the folded

wings (page 47).

3. Raise the tractor 3-point hitch just enough to lift the

parking stand bases off the ground. Set the hitch

circuit to Neutral. Shut off the tractor.

4. Raise the parking stands (page 36).
Note: The FOLD / FIELD switch may be in any position

for lift while folded.

Raise Pre-Folding (from Unfolded) 5-Section 2013+

These steps presume an applicator parked or stored

unfolded, already raised, but on lift-assist locks at rear,

on extended gauge wheels at wing tips, and on parking

stands at hitch.
1. Verify that lock channels are installed on the

lift-assist cylinders (page 45), that wing lock pins are

not in the locking holes (page 47) and that the

hydraulic harness is connected at the hitch

(page 34).

2. Raise the tractor 3-point hitch enough to lift gauge

wheels, coulters, and the parking stand bases off the

ground. Set the hitch circuit to Neutral.

Refer to Figure 35

3. Set the FOLD / FIELD switch to FIELD. This arrests

fold at field lift.

4. Retract the fold/lift circuit until lift-assist and wing fold

operations each their stops. Set fold/lift circuit to

Neutral. Shut off the tractor engine, leaving the

FOLD / FIELD switch powered-up

a

.

5. Raise the parking stands (page 36).

a. If the FOLD / FIELD switch is wired directly to the tractor battery, the tractor may be shut off completely. Otherwise leave the ACC active.

Figure 35

FOLD / FIELD Switch for Lift

34918

Gradual Crushing Hazard:

Do not rely on hydraulic pressure alone to keep the applicator

raised. Use parking stands (page 36) and locks (page 45)
when working around a raised applicator. The tractor hitch

may settle.

Equipment Damage Risk:

Do not fully fold or fully unfold while lowered. Perform
complete fold and unfold only when fully raised. When

lowered, the wing coulters near the wing pivots may be

damaged by bending or ground dragging.

Figure 36

Partial Fold in Field Lift

34922

Содержание Nutri-Pro NP30A













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды