GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 34

Страница: 34 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Preparation and Setup

Hitching Tractor to Applicator

This manual presumes the following (recommended)

operations sequence:
1. Hitch tractor to applicator for transport

2- and 3-Point Hitching: page 31

Pull-Type Hitching: below

2. Transport applicator separately from nurse tank:

page 66

3. Hitch nurse tank to applicator at field:

page 70

To prevent soil compaction on rows, set tractor wheels

between rows, for example: 60 inches center-to-center.

For hillsides and steep slopes, set tractor wheels as wide

as possible for maximum stability.

Pull-Type Hitching

Crushing Hazard:

Do not stand or place any body part between applicator and

moving tractor. You may be severely injured or killed by being
crushed between the tractor and applicator. Stop tractor

engine and set parking brake before attaching cables and

hoses.

Refer to Figure 5

1. Use parking jack to raise and lower applicator

tongue.

2. Back tractor draw bar into alignment with hitch.
3. Secure with a locking hitch pin .

Loss

of Control Hazard:

Do not operate without locking hitch pins. A pin working loose

could cause abrupt applicator motions resulting in a tank

upset and fertilizer release.

4. Secure safety chain to an anchor on the tractor.

Refer to Figure 5 and Figure 6

5. After hitching tractor to applicator, store jack on

storage stob on top of fertilizer applicator tongue.

Figure 5

Tongue on Jack

31081

Loss of Control / Public Safety Hazards:

Do not transport on public roads with a nurse tank hitched to

the applicator. Transport with an anhydrous ammonia nurse

tank hitched to an applicator is illegal in many places. See
“

Transport

” on page 66.

Figure 6

Jack on Storage Stob

31082

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды