GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 95

Страница: 95 / 172

NP30A or NP40A

Table of Contents

Index

Adjustments

2019-03-11

Table of Contents

Index

407-502M

Adjusting the Weight-Transfer

Note: See circuit diagrams in the Appendix starting on

Page 148.

Refer to Figure 66

1. In field conditions, unfold applicator (page 59).
2. Set FOLD / FIELD to FIELD.
3. Lower applicator (page 50), and set or check

application depth (page 38).

4. Pull forward to put coulters in ground.
5. Put tractor in Park and set parking brake.
6. Set tractor to half throttle. Extend the fold/lift circuit

(unfold). Lock lever for continuous operation.

7. Adjust tractor flow control valve so bypass gauge

needle is within the 1500 - 2200 PSI range. Larger

models will require the higher end of this range while

smaller models will want to be within the lower end.



NOTE

On older models without an electronic down pressure

valve, less PSI is required and pressure should fall

within the 1000 - 1500 PSI range.

8. Release the lock disc .
9. Adjust the knob for an initial value of 800 psi on

the gauge . Tighten the lock disc.

10. Check that bypass gauge is still in the green zone.

Adjust the tractor remote flow to correct. Re-check

the reading on the pressure-reducing gauge .

11. Observe applicator operation, and re-adjust

down-pressure as necessary after oil warm-up.

Repeat step 7 through step 10.

858-042C Rev. A

NOTICE

This machine is designed for continuous

hydraulic flow to the wing fold cylinders

during field operations. It is for use on

tractors having CLOSED CENTER

hydraulics only.

Engage the hydraulics (continuous flow) down.

2. From the cab, adjust the flow so the needle

on the bypass gauge is in the green zone

1000 to 1500 PSI.

3. At the valve, adjust the valve to set your

initial down pressure.

If the wings run high during operation, increase

pressure. if the center runs high, decrease

pressure.

SETTING DOWN PRESSURE VALVE

DOWN PRESSURE VALVE INSTRUCTIONS:

NUTRI-PRO

Figure 67

Weight Transfer Adjustment

34935

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды