GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 94

Страница: 94 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Adjustments

2013+ 2-Point 5-Section Weight Transfer

For 3-Section, Pull-Type, and 2012- 2-Point 5-Section,

see page 88.
See important safety information on page 87.

Description of system

Note: See circuit diagrams in the Appendix starting on

Page 148.

Inner wing fold cylinders can extend, during field

operation, to push the wings down using

mainframe/center weight. Weight transfer is enabled

by:
1. Set the FOLD / FIELD switch to FIELD.
2. Adjust the weight transfer valve.
The fold/lift circuit is set to continuous flow (in unfold

mode) to maintain the active weight transfer. This

system is designed for use with tractors having closed

center hydraulics. It is incompatible with open center

systems.
Note: Do not set or adjust the weight transfer system if

the outer wings are not level with the inner wings

at unfold. Do not use the weight transfer system to

compensate for unfold stop adjustment issues.

See “

Wing Leveling

” on page 92.

Adjust the weight transfer to achieve consistent coulter

depth, while keeping the wings level with the center

section. If insufficient weight is transferred, outside

(wing) coulters may run higher than center section. If

too much weight is transferred, center section may run

high.
If adjusted when the tractor is cold, re-adjustment may

be required when the oil warms. Monitor the pressure

gauges during early field operations.

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды