GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 119

Страница: 119 / 172

NP30A or NP40A

Table of Contents

Index

Maintenance and Lubrication

115

2019-03-11

Table of Contents

Index

407-502M

System Discharge

These steps are for clearing an applicator for service or

for storage near untrained persons. These instructions

presume that you have followed the steps at:

“

Stopping Application

” on page 77,

and the nurse tank is unhitched, per:

“

Final Nurse Tank Unhitch

” on page 80.

For a breakaway event, follow the instructions on

page 78 up through breakaway re-connection. Then

perform a normal shutdown (other than nurse tank

steps), per page 77.
The challenges in system discharge are:

• NH

liquid can remain in the system after the

recommended stopping procedures.

• NH

liquid self-cools as it evaporates, slowing

evaporation. It can take a long time for all of it to turn

to vapor, particularly in cooler weather.

• Once there is only vapor in the system, there is

usually little gas movement to drive the rest of it out.

• The tubing loops are usually the last to clear, and

may not fully clear. See sidebar.

Even if no ammonium hydroxide forms, the NH

vapor in

the system dilutes slowly with air. Harmless trace

amounts, noticed as occasional odor, may remain

indefinitely.

Normal Discharge

At the completion of stopping application and nurse tank

unhitching, all line valves are closed and all bleed valves

are open, and have been that way for at least an hour.

Transport may also have occurred, which aids clearing.
1. Verify that all line valves are closed, and all bleed

valves open. If this is not the case, there is risk of

trapped ammonia. See “

Clearing a Line Trap

” on

page 113.

2. Carefully walk down-wind of the applicator. Check

for ammonia odor. If pungent, there is at least some

pure NH

vapor in the system, and possibly some

liquid. Give the applicator some time to vent.

If there is no, or only mild odor, check the loops for

visible fluid. If only a few hours have elapsed since

application ended,

this liquid is pure NH

. Stay away

until it has vaporized.

3. From up-wind, check all the fittings and lines. If any

are cold (more than a few degrees below ambient

temperature), liquid evaporation is still in progress or

has only recently completed. Give the applicator

more time to vent.

Steps continue on next page...

Suffocation, Blinding, Burning, Freezing, Disabling and
Disfigurement Hazards:

Do not perform maintenance with anhydrous ammonia in the
system. Fully discharge the system of NH

liquid and vapor

before working on the applicator.

The delivery tubes are open to the atmosphere at the

knives or tines. When they don’t clear immediately, they

are likely to absorb atmospheric moisture, forming

ammonium hydroxide (NH

OH) in the tubes. This liquid

highly caustic

, and can persist for weeks or months,

but remains liquid at ambient temperatures, is harmless

to the tubing, and emits ammonia vapor slowly. If there

is liquid in the tubes, and it is not cold, it is likely to be

an NH

OH solution, and not pure NH

Figure 89

Delivery Loops

31617

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды