GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 172

background image

2019-03-11

Table of Contents

407-502M

NP30A or NP40A

Table of Contents

Applicator Operating Instructions

60

Unfolding and Folding 3-Point

Unfolding 3-Point

The 3-Point applicator should only be unfolded in the

field, or fully supported by parking stands.

Unfolding 3-Point (At Field)

These instructions presume the applicator has just

completed transport, and is being unfolded for field use.
1. Line the applicator up into the wind.
2. Close the weight-transfer shut-off valve (page 50).
3. Raise the 3-Point hitch fully.
4. Unfold the wings. Slowly extend the fold cylinders.

After the wings pass vertical, lock channels swing

into contact with the cylinder rods.

Stop the unfold when the wings are approximately

level. Hold at level with circuit Neutral.

5. Lower the applicator to the ground with the 3-point

hitch.

6. Open the weight-transfer shut-off valve.
7. Set the hitch to Depth Control mode.

Set the fold circuit to Float.

Unfolding 3-Point (Service)

To unfold, off field, for servicing, unfold with the center

section fully raised. Unless the wing gauge wheels have

been previously extended to maximum height, or extra

stands or supports are used, the wing end knives or tines

will reach the ground first. Take precautions if parking

surface damage is a concern.
1. Fully raise the 3-Point hitch.
2. Close the weight-transfer shut-off valve (page 50).
3. Point the applicator into the wind.
4. Deploy parking stands. Set them to maximum height.
5. Extend fold cylinders.
6. As the wings near level, set circuit to Neutral.
7. Unless using blocks or stands, fully extend the

gauge wheels to maximum height.

8. Resume unfolding until gauge wheels are on ground.

Set fold circuit to Float.

9. Lower the 3-point hitch.

Folding 3-Point

These instructions presume that the applicator is

unfolded and lowered.
1. Stop NH

3

flow (page 77).

2. Close the weight-transfer shut-off valve (page 50).
3. Retract the fold cylinder circuit until the wing locks

stop motion, or the outside row knives or tines just

start to lift out of the ground. Set the fold circuit to

Neutral.

4. Raise the 3-point hitch.
5. Wait for the delivery lines to discharge.
6. Deploy parking stands if the applicator is to be

parked at the folding spot.

Refer to Figure 41

(depicting an NP40L, which has similar wing locks)

7. Swing the wing locks up and out of their engaged

positions, and into their reset positions.

8. Retract the fold cylinders until the wings contact the

transport rest. Set circuit to Float if unhitching, or

Neutral for transport.

For parking/storage/service, lower the applicator onto

parking stands.

Figure 41: 3P:

Resetting Wing Locks

31620

1

2

Ammonia Exposure Hazard:

Face applicator up-wind or clear the delivery lines (page 116)
before unfolding. Fluid in delivery line loops, whether pure

NH

3

or concentrated NH

4

OH, is likely to move from the loops

and drip out at the knives or tines.

«
...
62
63
64
65
66
...
»

Содержание Nutri-Pro NP30A













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nutri-Pro NP30A

Бренд: Campden instruments Страницы: 8

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

KOMPAN SPF28666S

Бренд: Bommelland Страницы: 23

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: Major Страницы: 52

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: Jacobsen Страницы: 16

Бренд: Jacobsen Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды