GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 24

Страница: 24 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Introduction

Owner Assistance

If you need customer service or repair parts, contact a

Great Plains dealer. They have trained personnel, repair

parts and equipment designed for Great Plains products.

Refer to Figure 2 and Figure 3

Your machine’s parts were specially designed and

should only be replaced with Great Plains specified

parts. Always use the serial and model number when

ordering parts from your Great Plains dealer.
For 2013 and later 5-section applicators, the serial

number plate is located on the center section, on the

front face of the left front fold cylinder mount.
On 3-section applicators, and 2012 and earlier 5-section

models, the serial-number plate is located on the left

face of the top 3-point hitch weldment.
Record your NP30A or NP40A Fertilizer Applicator

model and serial number here for quick reference:
Model Number:__________________________
Serial Number: __________________________

Further Assistance

Great Plains Manufacturing, Inc. and your Great Plains

dealer want you to be satisfied with your new NP30A,

NP40A. If for any reason you do not understand any part

of this manual or are otherwise dissatisfied, please take

the following actions first:
1. Discuss the matter with your dealership service

manager. Make sure they are aware of any problems

so they can assist you.

2. If you are still unsatisfied, seek out the owner or

general manager of the dealership.

If your dealer is unable to resolve the problem or the

issue is parts related, please contact:

Great Plains Service Department

1525 E. North St.

P.O. Box 5060

Salina, KS 67402-5060

Or go to www.greatplainsag.com and follow the contact

information at the bottom of your screen for our service

department.

Figure 2

2013+ 5-Section S/N Location

36030

Model # NP40

A-25S

Figure 3

3S & 2012- 5S S/N Location

31057

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды