GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 92

Страница: 92 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Adjustments

3-Section, Pull-Type, and 2012- 2-Point

Weight Transfer

For 2013+ 2-Point 5-Section weight transfer, see

page 90.
See important safety information on page 87.

Description of system

Note: See circuit diagrams in the Appendix starting on

Page 148.

Refer to Figure 65

Wing fold cylinders can extend, during field operation,

to push the wings down using mainframe/center weight.

Weight transfer is enabled by opening the weight-

transfer shut-off valve, and controlled by two adjustment

valves. The fold circuit is set to continuous flow (in unfold

mode) to maintain the active weight transfer.
The weight-transfer shut-off valve must be open for

weight transfer. When closed, it bypasses the reducing

valve for faster fold cylinder operation (and faster 2-point

lift-assist).
The pressure reducing valve controls the flow to the

cylinders.
The bypass valve returns excess oil to the tractor.
Adjust the weight transfer to achieve consistent coulter

depth, while keeping the wings level with the center

section. If insufficient weight is transferred, outside

(wing) coulters may run higher than center section. If too

much weight is transferred, center section may run high.
If adjusted when the tractor is cold, re-adjustment may

be required when the oil warms. Monitor the pressure

gauge during early field operations.

Figure 65

Weight Transfer Valves

32041

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды