GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 70

Страница: 70 / 172

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

Transport

Loss of Control Hazard:

Never use the applicator to tow a nurse tank on public roads.

Tow the tank to the field with a separate vehicle. The
applicator cannot provide sufficient lateral control of a

trailing cart at highway speeds. The total weight of the train

can also easily exceed the steering and/or braking capability
of the tractor. A tank upset could occur during normal highway

maneuvers. The resulting accident or spill could cause serious

injury or death. Highway towing of an anhydrous ammonia
tank behind an applicator is prohibited by law in many

locales.

Loss of Control Hazard (2P, Pull-Type):

Never tow a pull-type or 2-point applicator that weighs more
than 150% of the tractor (transport tractor must weigh at least

67% of applicator). Ensure that the towing vehicle is adequate

for the task. Using an inadequate tow vehicle is extremely
unsafe, and can result in loss of control, serious injury and

death.

Tractor weight matters. For field configuration (after

transport), tractor must weigh at least 150% of the applicator

plus the loaded nurse tank. This weight is substantially higher
than the required transport weight.

Loss of Control Hazard (2P, 3P):

Never transport a 2-point or 3-point applicator unless the

tractor is properly ballasted to provide adequate weight on the
steering wheels. A heavy 2-point or 3-point applicator can

dangerously reduce steering control. A normal turn could
result in an accident and serious injury or death. Check your

tractor manual for ballasting requirements.

Tractor weight matters. For field configuration (after

transport), tractor must weigh at least 150% of the applicator

plus the loaded nurse tank. This weight is substantially higher
than the required transport weight.

Braking and Loss of Control Hazard:

Do not exceed 20 mph (32 kph).

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Похожие инструкции для Nutri-Pro NP30A

Бренды по названию

Популярные бренды