GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 77

Страница: 77 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Bleeding Marker Hydraulics

Crushing Hazard:

You may be injured if hit by a folding or unfolding marker.

Markers may fall quickly and unexpectedly if the hydraulics

fail. Never allow anyone near the drill when folding or
unfolding markers.

1. Review warnings, bleeding notes and system

information on page 69.

Refer to Figure 77

2. With markers unfolded in field position, crack

hydraulic-hose JIC fittings at base and rod ends of

each marker cylinder.

3. With tractor at idle speed, activate tractor hydraulic

valve forward until oil appears at a fitting. When oil

begins to seep out around a fitting, tighten that fitting.

Reverse the tractor hydraulic valve until oil appears

at opposite hose fitting. Tighten that fitting.

4. If you have dual markers, activate tractor hydraulic

valve forward again until oil seeps out around a

fitting on the other marker cylinder. Tighten that

fitting. Reverse tractor hydraulic valve until oil seeps

out around remaining hose fitting and tighten it.

5. Fold and unfold markers slowly to work out all air.



NOTE:

Use caution when folding and unfolding markers for

the first time, checking for pinching and kinking of

hoses.

In-Line Filters

If the raising or lowering times of the openers slow

noticeably, check the in-line filters and clean if needed.

Refer to Figure 78

Two filters are located on one each of the down-pressure

adjustment valves. If the Point Row option is installed,

another filter is located on the third adjustment valve.

Figure 77

Bleeding Marker Hydraulics

18942

Figure 78

In-Line Filter Locations

22968

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды