GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 80

Страница: 80 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

Wing Box Alignment

1. Place a block ahead of the wing gauge wheels.

Refer to Figure 83

2. Pull forward against blocks to rock wing frames

back. Pull forward until stop bolts are firmly

against toolbars.

Refer to Figure 84

3. Check for proper alignment by running a string line

across back of drill toward outer ends of wings.

4. For proper alignment, outside ends of boxes

should be about 1in (2.5cm) ahead of inside ends .

5. To adjust box alignment, shorten or lengthen stop

bolts to change the contact point with the toolbars.

Loosen jam nut and thread stop bolt in or out. Adjust

stop bolts in or out until outside ends of boxes are

1in (2.5cm) ahead of inside ends.

6. Tighten jam nut.

Figure 83

Stop Bolts (Wings Folded)

17357

Figure 84

Wing Box Alignment Measurement

17300

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды