GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 38

Страница: 38 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Active Hydraulic Systems

1. Lock hydraulic lever forward during field operation

for constant hydraulic flow to openers.

John Deere tractors with Sound-Gard ® Body

Use lever lock clip, John Deere part number

R52667, to lock lever forward. See your tractor

dealer for clip purchase and installation.

John Deere 7000 Series tractors

: Rotate valve

detent selector to motor position to lock lever in

forward position.

John Deere 8000 Series tractors

: Set timer to

continuous. Push lever forward until detent clicks.

Case-IH Magnum tractors

: Lock lever forward in

detent position. You may need to turn up detent

pressure to its maximum setting. Do not tie hydraulic

lever past detent position with a strap. See your

tractor dealer for hydraulic-system details.

Other tractors

: Lock lever forward in detent

position. You may need to turn up detent pressure to

maximum or use a mechanical detent holder to hold

lever forward. See your tractor dealer for proper

means of providing constant flow to openers.

Refer to Figure 29

2. With tractor hydraulic lever locked forward and

openers in field position, release lock disk and set

down pressure with adjustment knob . Watch

pressure gauge and dial in desired pressure on

openers. There is one pressure-control valve for

inboard openers (“CENTER”) and one for outboard

openers (“WING”). If the Point Row option is

installed, the controls are Left (“LEFT”) and Right

(“RIGHT”).



NOTE:

Rotate knob clockwise to increase pressure and

counterclockwise to decrease pressure.

3. Once pressure is set, set knobs with lock disks .
4. In some applications, pressure on inboard end of

wings (CENTER) is set slightly higher than the

outboard ends (WINGS) to account for additional

compaction from drill transport tires and tractor tires.

The recommended pressure range for drilling is

between 1200 psi and 1800 psi, and initially 1400 psi

5. For more information on adjusting hydraulic down

pressure, see “

Row Unit Down Pressure (Spring)

”

on page 58.

Equipment Damage Risk:

Tractors with load-sensing hydraulics must use the bypass
valve to operate the 2S-2600/F/HD/HDF. Failure to use the

bypass valve can cause major tractor damage. Before

adjusting opener down pressure, set bypass valve per “

Setting

the Bypass Valve

” on page 20.

Equipment Damage Risk:

During operation always raise openers before turning. Never

back up or turn sharply with openers in the ground. Doing so
will plug openers and may damage equipment.

Inconsistent Population Risk:

Do not operate at pressures so high that the gauge wheels

loose traction, or are off the ground, resulting in skips and

poor seed metering.

Figure 29 - Active

Pressure Control Valves

26477

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды