GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 73

Страница: 73 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Bleeding Hydraulics

To function properly, the hydraulics must be free of air. If

hydraulics have not been bled, they will operate with

jerky, uneven motions and could cause wings to drop

rapidly during folding or unfolding. If hydraulics were not

bled during initial implement setup or if you replace a part

in hydraulic system during the life of the drill, complete

the following procedures.

High Pressure Fluid Hazard:

Escaping fluid under pressure can penetrate the skin causing

serious injury. Avoid the hazard by relieving pressure before
disconnecting hydraulic lines. Use a piece of paper or

cardboard, NOT BODY PARTS, to check for suspected leaks.

Wear protective gloves and safety glasses or goggles when
working with hydraulic systems. If an accident occurs, seek

immediate medical attention from a physician familiar with

this type of injury.

Negative Tongue Weight Hazard:

Raising openers on unfolded, unhitched drill will cause drill

tongue to rise suddenly, which could cause serious injury or

death. Be certain that drill is hitched securely to your tractor
drawbar and the safety chain is securely attached to tractor

before raising openers or unfolding drill.

Bleed only at:

JIC (Joint Industry Conference, 37



flare) or

NPT (National Pipe Thread, tapered thread) fittings.

Never bleed at:

ORB (O-Ring Boss) or
QD (Quick Disconnect) fittings.

Check hydraulic fluid level in tractor reservoir and fill to

proper level. Add fluid to system as needed.



NOTE:

System capacity for entire drill is about



U.S. gallons

(17 liters).

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды