GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 76

Страница: 76 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

Bleeding Transport Lift Hydraulics

Refer to Figure 76

1. Review warnings, bleeding notes and system

information on page 69.

2. With drill lowered into field position, loosen

base-end-hose fitting at elbow on right-hand
transport-lift cylinder .

3. Slowly supply oil to base end of transport-lift

cylinders until oil appears at the loosened hose

fitting. As oil appears at fitting, tighten that fitting.

4. Completely extend transport-lift cylinders and

immediately lock cylinders up by flipping up cylinder

lock channels on both transport-lift cylinders. See

“

Raising Drill (Transport Lift)

” on page 27.

Crushing Hazard:

The hydraulics could fail, causing the openers to fall and

crush you. To prevent serious injury or death, always secure

cylinder lock channels over extended transport-lift cylinders
before working under openers.

5. When cylinder lock channels are in place, loosen

rod-end-hose fitting at elbow on left transport-lift
cylinder .

6. Slowly supply oil to rod end of transport-lift cylinders

until oil appears at loosened hose fitting. As oil

begins to appear at fitting, tighten that fitting.

7. Extend transport-lift cylinders and remove cylinder

lock channels. Completely cycle transport-lift

hydraulics several times.

Figure 76

Bleeding Opener Lift Hydraulics

17298

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды