GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 19

Страница: 19 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Introduction

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Owner Assistance

If you need customer service or repair parts, contact a

Great Plains dealer. They have trained personnel, repair

parts and equipment specially designed for Great Plains

products.

Refer to Figure 2

Your machine’s parts were specially designed and

should only be replaced with Great Plains parts. Always

use the serial and model number when ordering parts

from your Great Plains dealer. The serial-number plate is

located on the left side of the drill frame below the front of

the seed box.
Record your drill model and serial number here for quick

reference:
Model Number:__________________________
Serial Number: __________________________

Further Assistance

Great Plains Manufacturing, Inc. and your Great Plains

dealer want you to be satisfied with your new 2S-2600. If

for any reason you do not understand any part of this

manual or are otherwise dissatisfied, please take the

following actions first:
1. Discuss the matter with your dealership service

manager. Make sure they are aware of any problems

so they can assist you.

2. If you are still unsatisfied, seek out the owner or

general manager of the dealership.

If your dealer is unable to resolve the problem or the

issue is parts related, please contact:

Great Plains Service Department

1525 E. North St.

P.O. Box 5060

Salina, KS 67402-5060

Or go to www.greatplainsag.com and follow the contact

information at the bottom of your screen for our service

department.

Figure 2

Serial Number Plate

17315

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды