GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 33

Страница: 33 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Transport

Loss of Control Hazard:

Towing the drill at high speeds or with a vehicle that is not

heavy enough could lead to loss of vehicle control. Loss of
vehicle control could lead to serious road accidents, injury

and death. To reduce the hazard:

Do not exceed 20 mph.

Do not tow a drill that, when fully loaded, weighs more than
1.5 times the weight of the towing vehicle.

In the following table, multiply the total drill weight by
0.67 (



) to determine minimum tractor weight.

Weights for Tractor Requirements

Marker Transportation

Refer to Figure 25

Always transport markers folded flat. Make sure second
marker section rests securely on transport carrier .

Drill Weight (Pounds / Kilograms)

Drill Model

2S-2600-5206

2S-2600HD-5206

2S-2600-4275

2S-2600-3210

Standard

“00”

“00HD

” Drill

10423 lbs / 4728 kg

10404 lbs / 4719 kg

10386 lbs / 4711 kg

For

“F”

and “

HDF

” Model, add...

+910 lbs / +413 kg

+889 lbs / +403 kg

+869 lbs / +394 kg

With Dual Markers, add...

+887 lbs / +402 kg

For Full Main Box Seed Load, add...

+5389 lbs / +2444 kg

Small Seeds Option

+619 lbs / +281 kg

+603 lbs / +273 kg

+586 lbs / +266 kg

Maximum Configuration:

(2S-2600F and HDF, Dual Markers,

Seed Loaded, Small Seeds)

18228 lbs / 8268 kg

18172 lbs / 8243 kg

18117 lbs / 8218 kg

Figure 25

Marker in Transport Cradle

18857

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды