GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 48

Страница: 48 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Shaft Monitor Operation

The optional shaft monitor generates an alarm if either of

the two main seed box meter shafts on the drill stop
turning for more than 20 seconds.

Refer to Figure 44

To operate shaft monitor, turn system on by activating
on-off switch on monitor head. If seed-cup shafts are
turning, both indicator lights are illuminated and no

alarm sounds.
If any seed-cup shaft stops for 20 seconds, an alarm

sounds and the indicator for that section flashes on the

monitor, designating the failed shaft.



NOTE:

The 20-second delay is to prevent nuisance alarms

when turning at the end of the field.



NOTE:

If a failure does occur and an alarm sounds,

remember you have traveled for 20 seconds without

planting with that drill section. If due to wheel lift or low

tire pressure, you may have been planting at

progressively lower populations before that.

Electronic Acremeter

Refer to Figure 45

A battery-operated electronic acre counter is supplied

with the drill. The display module for the system is

normally on the front face of the main toolbar near the

left gauge wheel and close to the sensor. (For 2S-2600

models the meter is mounted on the right hand box

frame.)
If your drill was equipped with this acremeter from

production, it will have been supplied already

programmed
The acremeter calculates and displays the field acres

and total acres accumulated.
The meter counts rotations of the main ground drive

shaft before the clutch. The meter tallies all movements

with the drill unfolded, whether planting or not.
The counter operates in one of two modes, in

sleep

mode or in

entry

mode. (See separate manual

194-074M specifically for operations of this meter).

a. The older Vansco shaft monitor was 30 seconds.

Figure 44

Shaft Monitor Head

27049

Figure 45

Electronic Acremeter

34776

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды