GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 7

Страница: 7 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Important Safety Information

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Keep Riders Off Machinery

Riders obstruct the operator’s view. Riders could be

struck by foreign objects or thrown from the machine.



Never allow children to operate equipment.



Keep all bystanders away from machine when

folding/unfolding, raising/lowering markers,
raising/lowering openers, and transporting.

Transport Machinery Safely

Maximum transport speed for drill is 20 mph (32 kph).

Some rough terrains require a slower speed. Sudden

braking can cause a towed load to swerve and upset.



Do not exceed 20 mph (32 kph). Never travel at a speed

which does not allow adequate control of steering and
stopping. Reduce speed if towed load is not equipped with
brakes.



Comply with national, regional and local laws.



Follow your tractor manual recommendations for

maximum hitch loads. Insufficient weight on tractor
steering wheels will result in loss of control.



Carry reflectors or flags to mark drill in case of breakdown

on the road.



Keep clear of overhead power lines and other obstructions

when transporting. Refer to transport dimensions under
“

Specifications and Capacities

” on page 95.

Check for Overhead Lines

Drill markers contacting overhead electrical lines can

introduce lethal voltage levels on drill and tractor frames.

A person touching almost any metal part can complete

the circuit to ground, resulting in serious injury or death.

At higher voltages, electrocution can occur without direct

contact.



Avoid overhead lines during seed loading/unloading and

marker operations.

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Бренды по названию

Популярные бренды