GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 35

Страница: 35 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Unfolding

Certain Tire Damage

Do not lower openers until drill in unfolded or you will

damage drill tires.

Drill must be left raised (transport and opener lift) prior to

unfolding.
1. Verify that the site has clearance needed to unfold

drill.

2. If equipped with markers, set Marker/Fold valve at

hitch to Fold.

3. Verify that the Transport Lift circuit is still raised, and

transport cylinder lock channels are installed.

Refer to Figure 23

4. Verify that the opener sub-frames are still raised and

locked up (handles in ROAD position).

Refer to Figure 27

5. At fold latch, prop both latch pawls on the wing

pins, raising the latches off the pins.

6. Slowly supply oil to base end of fold circuit. Unfold

wing frames by completely extending fold cylinders.

If field operations are planned:
7. Lower drill mainframe. See “

Unfolding

” on page 31.

8. Lower opener subframe. See “

Lowering Openers

”

on page 26.

Null4.aac:

Figure 26 - Unfold

Opener Unlock

15549

Figure 27

Latch Ready for Unfold

17319

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Бренды по названию

Популярные бренды