GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 26

Страница: 26 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Preparation and Setup

Marker Setup

Refer to Figure 12

Markers are field-installed, but usually do not have their
extension length precisely set. The drill must be

leveled per “

Leveling the Drill

” on page 74, and

marker(s) must be in correct working order per “

Marker

Maintenance

” on page 77.

Row unit centerline stations on 2S-2600 drills are

symmetrical about machine center, so left and right

extensions are normally identical, for both opposing and

concentric passes.
Set the initial length of the marker(s) as follows:
1. With drill unfolded, lower drill and openers to field

position (“

Raising and Lowering Openers

” on page

26).

2. Extend a marker on one side. Pull forward several

feet to leave a mark.

3. Sighting parallel to the main toolbar, measure

from the centerline of the left outside row unit to the

mark.

4. Adjust the marker extension so that the mark is

one half the span plus one row unit spacing .

See “

Marker Adjustments

” on page 62 for setting

marker extension.

5. Pull forward several feet, and re-measure to verify

any adjustment. Validate the mark by making a pass

to one or both sides.

6. Fold marker. Extend other side and adjust.

Point Row Cab Module

If your drill has the Point Row option, the cab module

may already have been installed by your dealer. If not,

consult the installation instructions for the option, and

mount the module in a convenient location.



NOTE:

If field conditions require inverting the marker disk

(page 64), the mark moves, and the extension needs

to be re-measured and reset. Marking also changes

slightly if the opener frame trunnion position is

changed (page 54).

Figure 12

Marker Extension

Model

Spacing

Extension

2S-2600-3210

10 in

165.0in

(419.1cm)

2S-2600-4275

7.5 in

161.75in

(410.8cm)

2S-2600-5206

6 in

160.25in

407.0cm

Figure 13

Point Row Cab Module

22692

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды