GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 68

Страница: 68 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Adjustments

Marker Disk Adjustment

Sharp Object Hazard:

Marker disks may be sharp. Use caution when making

adjustments in this area.

Mark Width

Refer to Figure 70

is the direction of travel.

To change angle of cut, and the width of the mark, loosen



-inch bolts holding the disk assembly.

For a wider mark , increase the angle of the marker
with respect to the tube . For a narrower mark ,

reduce the angle.
Tighten bolts .

Direction of Cut

To have the marker throw dirt out, invert the disk on the

spindle, and invert the disk assembly.

Figure 70

Marker Disk Angle

11757

Figure 71

Marker Disk Inverted

11248

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды