GRASS VALLEY K2 SAN Скачать руководство пользователя страница 283

Страница: 283 / 346

3. Verify adapter names.

•

On a Dell R620 or R610 system with four 1 Gig adapters only, the required names are specified
as follows:

Adapter name

Control Connection

FTP-Streaming Connection

Unused Connection 1

Unused Connection 2

•

On a Dell R620 system with two 1 Gig adapters and two 10 Gig adapters, the required adapter
names are specified as follows:

Adapter name

Control Connection

Unused Connection 1

FTP-Streaming Connection

Unused Connection 2

•

On a Dell R610 system with a 10 Gig network interface card installed, the required adapter
names are specified as follows:

Adapter name

Control Connection

Unused Connection 0

Unused Connection 1

Unused Connection 2

FTP 10G Connection

The 10 Gig network interface adapter is named

FTP 10G Connection

. If it has dual-ports,

the other connection is named

Unused Connection 3 10G

4. Proceed as follows:

•

If all the names on this system are configured correctly to locations, skip the rest of this
procedure.

•

If names on this system are not configured correctly, for each adapter name incorrectly
configured, complete the remaining steps of this procedure.

5. Select the name in the Name column.

6. Select

File | Rename

to enter rename mode.

7. Type the name required.

2014 01 27

K2 SAN Installation and Service Manual

283

Administering and maintaining the K2 SAN

Содержание K2 SAN



























































































































































































































































































































































Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды

GRASS VALLEY K2 SAN, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды