GRASS VALLEY K2 SAN Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 346

background image

16. On the Partition or Disk to Restore page, select

(D:)

and then click

Next

.

17. On the Restored Partition Location page, select

(D:)

and then click

Next

.

opens.

18. On the Restored Partition Type page, leave the selection at

Primary

and then click

Next

.

19. On the Restored Partition Size page, leave settings at their defaults. The size reported in the upper

pane is the size detected of the actual D: partition. This should be the same as that reported in
the Partition size field in the middle of the page. Free space before and Free space after should
both be reported at 0 bytes. Click

Next

.

20. On the Next Selection page, select

No, I do not

and then click

Next

.

21. On the Restoration Options page, do not make any selections. Click

Next

.

22. On the “…ready to proceed…” page, verify that you are restoring the correct image to the correct

location. Click

Proceed

.

23. On the Operation Progress page, observe the progress report.

24. When a message appears indicating a successful recovery, click

OK

.

25. Click

Operations | Exit

to exit the Acronis True Image program.

The machine restarts automatically.

26. Remove the recovery media while the machine is shutting down.

27. When prompted, enter the machine name.

Make sure the name is identical to the name it previously had.

At first start up after reimage, the system is in Embedded Security Update mode by default.

Next, do the following to restore the K2 Media Server to its factory-default state. Refer to related
topics in this document or as otherwise indicated.

1. Set up Windows.
2. Restore network configuration.
3. Install the SiteConfig Discovery Agent.
4. Install SNFS software manually. Do not use SiteConfig.
5. Restart.
6. Install K2 software manually. Do not use SiteConfig.

While manually installing software, accept any hardware installation or driver/security prompts
that appear. Also refer to related topics in "K2 Release Notes".

7. Install Fibre Channel Card driver.
8. Activate Windows within 30 days.

Related Topics

Embedded Security modes and policies

on page 116

Setting up Windows

on page 115

Restoring network configuration

on page 282

Installing the Discovery Agent on a K2 Media Server

on page 114

Installing the Fibre Channel card driver

on page 288

Activating the Windows operating system

on page 116

2014 01 27

K2 SAN Installation and Service Manual

109

Managing K2 Software

«
...
107
108
109
110
111
...
»

Содержание K2 SAN



























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SAN

Бренд: IBM Страницы: 62

LaCie Ethernet Big Disk

Бренд: LaCie Страницы: 16

4BIG QUADRA USB 3.0

Бренд: LaCie Страницы: 41

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

Бренд: LaCie Страницы: 13

Бренд: LaCie Страницы: 29

Бренд: LaCie Страницы: 4

Rugged Triple USB 3.0

Бренд: LaCie Страницы: 2

Rugged Triple USB 3.0

Бренд: LaCie Страницы: 2

Бренд: LaCie Страницы: 5

RUGGED BOSS SSD

Бренд: LaCie Страницы: 60

Бренд: LaCie Страницы: 2

Little Big Disk Quadra

Бренд: LaCie Страницы: 4

Little Big Disk Quadra

Бренд: LaCie Страницы: 24

Бренд: LaCie Страницы: 53

Бренд: LaCie Страницы: 59

5BIG THUNDERBOLT 2

Бренд: LaCie Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды