GRASS VALLEY K2 SAN Скачать руководство пользователя страница 188

Страница: 188 / 346

Configure File System Server Configuration page - NH server

This page checks on the file system server role. The server also functions as a file system client,
which is also checked from this page.

1. Do not select

Reserved Bandwidth

unless instructed to do so by Grass Valley. This system is

usually not configured for RVIO.

2. Click

Launch Storage Manager

Storage Utility opens.

3. Leave the Configure K2 Server wizard open while you use Storage Utility.

When you are done with Storage Utility, you continue with the wizard.

Next, use Storage Utility to configure the RAID storage and file system.

Configuring RAID

Use Storage Utility to complete the configuration of the K2 RAID storage devices, as explained in
the following topics.

Configuring RAID network and SNMP settings - Basic

Prerequisites for the K2 RAID chassis are as follows:

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

•

Power on

Prerequisites for the optional K2 RAID Expansion chassis (if present) are as follows:

•

Fibre channel cable(s) connected

188

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Содержание K2 SAN



























































































































































































































































































































































Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды

GRASS VALLEY K2 SAN, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды