GRASS VALLEY K2 SAN Скачать руководство пользователя страница 197

Страница: 197 / 346

Check the V: drive

Prerequisites:

•

The K2 Media Server is configured

•

The restart of the K2 Media Server after it is configured is complete

This task is required for NAS server functionality.

1. Verify that the K2 Media Server has restarted by opening the MS-DOS command prompt and

use the “ping” command.

2. In the K2Config application tree view, under the K2 Media Server select the File System Server

node.

The File System Server Configuration page appears.

3. Click

Check

and verify that the V: drive is shared.

The K2 Nearline SAN configuration is complete.

Configuring the redundant nearline K2 SAN

Work through the topics in this section sequentially to configure a redundant nearline (Tier 3) K2
SAN.

Prerequisites for initial configuration - Nearline K2 SAN

Before beginning your initial configuration, make sure the devices of the K2 SAN meet the following
prerequisites.

Control point PC

•

Ethernet cable connected

•

Control Point software installed

•

Control network IP address assigned

•

Network communication over the control network with all other K2 devices

•

Power on

Ethernet switch

•

Ethernet cables connected

•

Control network IP address assigned

•

VLANs set up

•

Trunks set up

•

Power on

2014 01 27

K2 SAN Installation and Service Manual

197

Configuring and licensing the K2 SAN

Содержание K2 SAN



























































































































































































































































































































































Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды

GRASS VALLEY K2 SAN, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды