GRASS VALLEY K2 SAN Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 346

background image

3. Shut down any remaining K2 Media Servers, such as NH FTP servers.

Next, power off K2 RAID devices.

Powering off K2 G10v2 RAID

Prerequisites for this task are as follows:

•

K2 Media Servers are powered off

1. On the primary RAID chassis controller, identify the Ready LED. It blinks at a rate of 1 blink

per second during normal operation.

2. Tap the power button on a RAID controller. If you have two controllers, you can tap the power

button on either RAID controller 0 or RAID controller 1.

NOTE: Do not press and hold down the power button.

After tapping the power button, the Ready LED blinks more quickly, at a rate of about 2 blinks
per second.

The power button on the RAID controller turns off power for the primary RAID chassis and any
connected Expansion chassis. Power-off normally occurs within 20 seconds and is indicated
when LEDs other than those on the power supplies go off and the fans stop rotating.

3. Wait for RAID power-off to complete before proceeding.

4. Power-off all Ethernet switches.

5. Power-off the control point PC and/or the SNMP manager PC, if necessary.

Next, power off remaining SAN devices.

Power off remaining K2 SAN devices

1. Power-off all Ethernet switches.

2. Power-off the control point PC and/or the SNMP manager PC, if necessary.

The K2 SAN is powered off.

Powering on the K2 SAN

Use the following procedures to do an orderly power on of the complete K2 SAN.

236

K2 SAN Installation and Service Manual

2014 01 27

Operating the K2 SAN

«
...
234
235
236
237
238
...
»

Содержание K2 SAN



























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SAN

Бренд: Quantum Страницы: 32

Бренд: U-Line Страницы: 5

Бренд: Patiowell Страницы: 27

Бренд: Keter Страницы: 2

Automotive Work Stations

Бренд: Borroughs Страницы: 3

Бренд: IBM Страницы: 60

Бренд: Apricorn Страницы: 36

IC25N040ATCS04 - Travelstar 40 GB Hard Drive

Бренд: IBM Страницы: 217

Бренд: Clarke Страницы: 8

AltaVault System

Бренд: NetApp Страницы: 2

Aspire EASYSTORE H341

Бренд: Acer Страницы: 59

Aspire EASYSTORE H341

Бренд: Acer Страницы: 74

Aspire EasyStore Series

Бренд: Acer Страницы: 148

Aspire easyStore H340

Бренд: Acer Страницы: 68

Altos EasyStore

Бренд: Acer Страницы: 169

Aspire easyStore H340

Бренд: Acer Страницы: 148

Altos EasyStore

Бренд: Acer Страницы: 7

Бренд: EDSLab Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды