GRASS VALLEY K2 SAN Скачать руководство пользователя страница 118

Страница: 118 / 346

Manage Embedded Security Update mode

1. From the Windows desktop, click

Start | All Programs | Grass Valley | Embedded Security Manager

Embedded Security Manager opens.

Interpret Current Status as follows:

•

Enabled

: Embedded Security is enabled but is not in Update mode.

•

Update

: Embedded Security is enabled and is in Update mode, ready for software installation.

2. Manage the Update mode as follows:

•

If Embedded Security is not in Update mode, click

Enter

to put it in Update mode.

•

If Embedded Security is already in Update mode, click

Leave

to take it out of Update mode.

A restart is not required after you change the Update mode.

118

K2 SAN Installation and Service Manual

2014 01 27

Managing K2 Software

Содержание K2 SAN



























































































































































































































































































































































Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды

GRASS VALLEY K2 SAN, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 SAN

Отзывы:

Похожие инструкции для K2 SAN

Бренды по названию

Популярные бренды