GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 284 | Manualshive

Страница: 284 / 366

background image

4. Allow the failover process to complete, until K2server2 is operating correctly in its new role as

the primary K2 Media Server for the K2 SAN.

5. Verify K2server2 as primary.

6. Start up K2server1. It is now out of service. If you need to do service work on K2server1, you

can do it now. After your work is complete, proceed with the next step.

7. If there are K2 Media Servers with role of iSCSI bridge or Fibre Channel switches on the same

redundant “side” as K2server1, start or restart them.

8. In Server Control Panel, for K2server1, click

Start

. This notifies K2server2 (via a heartbeat signal

on the serial cable) that K2server1 is coming online as backup.

9. Verify K2server1 as backup.

10. All failover processes are complete. All media management mechanisms are now running and

K2server1 is now qualified and acting as the backup.

Recovering from a failover

WARNING: Do not attempt this procedure except under the supervision of qualified Grass
Valley personnel.

In the following procedures, K2server1 and K2server2 represent your redundant K2 Media Servers.
The procedure begins with K2server1 being the server on the failed side of the SAN. K2server2 is
acting as the primary K2 Media Server.

1. Verify primary/backup roles and make sure K2server2 is the primary.

2. Start up K2server1. It is now out of service.

3. Determine the cause of the failover and take corrective action as necessary. If you need to do

service work on K2server1 or other devices on the failed side of the SAN, you can do it now.
After your work is complete, proceed with the next step.

4. If there are K2 Media Servers with role of iSCSI bridge, Ethernet switches, or Fibre Channel

switches on the same redundant “side” as K2server1, start or restart them. Make sure they have
been started up at least once before putting K2server1 into service.

5. In Server Control Panel, for K2server1, click

Start

. This notifies K2server2 (via a heartbeat signal

on the serial cable) that K2server1 is coming online as backup.

6. Verify K2server1 as backup.

7. All failover processes are complete. All media management mechanisms are now running and

K2server1 is now qualified and acting as the backup.

Related Topics

Powering on the K2 SAN

Working with K2 Media Servers

Use the procedures in this section when doing configuration or service work on a K2 Media Server
that is part of an operational K2 SAN.

284

K2 SAN Installation and Service Manual

02 February 2012

Administering and maintaining the K2 SAN

«
...
282
283
284
285
286
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: Sencore Страницы: 112

Бренд: Audio Note Страницы: 7

Бренд: LEGRAND Страницы: 4

Бренд: Moxa Technologies Страницы: 2

Mediagate MG-450HD

Бренд: AL Tech Страницы: 100

ICT206012-100AI2

Бренд: ICT Страницы: 2

Бренд: Faulhaber Страницы: 29

ROTAPULS CK61 Series

Бренд: Lika Страницы: 2

Al-Mu'allim AM-RD2

Бренд: PLAYNETICS Страницы: 21

Бренд: Van Medevoort Страницы: 10

Бренд: D&H Страницы: 106

Бренд: Cross Technologies Страницы: 18

Бренд: Motrona Страницы: 28

Бренд: Samlexpower Страницы: 48

Бренд: AEG ID Страницы: 20

Бренд: Wellav Страницы: 24

Бренд: Lika Страницы: 80

Бренд: Sollae Systems Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды