GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 338

Страница: 338 / 366

4. In the switch’s configuration application, choose

Configuration

, then

Device Features

5. Set Spanning Tree to

and click

Apply Changes

If prompted, log in with the switch’s administrator username and password.

6. Close the switch configuration application.

7. Restart the switch to put changes into effect.

Upgrading firmware on HP switch

1. If you have not already done so, install a TFTP Server.

For example, to install

tftpd32.exe

, go to

http://tftpd32.jounin.net/

2. Open the TFTP Server.

3. Make sure your current working directory includes the

*.swi

file that you are using for the

upgrade.

4. Execute the copy command with the following syntax:

copy tftp flash <ip-address> <remote-os-file> [ < primary | secondary

> ]

Note that if you do not specify the flash destination, the TFTP download defaults to the primary
flash.

For example, to download a software file named T_13_23.swi from a TFTP server with the IP
address of 10.16.34.3 1, use the following:

ProCurve # copy tftp flash 10.16.34.3 T_13_23.swi

5. When prompted

The primary OS image will be deleted. continue [y/n]?

, press

When the switch finishes downloading the software file from the server, it displays the progress
message

Validating and Writing System Software to FLASH...

338

K2 SAN Installation and Service Manual

02 February 2012

Administering and maintaining the K2 SAN

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды

GRASS VALLEY K2 BASECAMP EXPRESS, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды