GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 282 | Manualshive

Страница: 282 / 366

background image

2. Click the

Server Control Panel

button. The Server Control Panel opens.

3. Identify the primary K2 Media Server and the backup K2 Media Server.

If the K2 SAN does not have redundant servers, only one server (the left half of the Server Control
Panel) is displayed.

For Nearline K2 SANs, the Server Control Panel is not available from the K2Config application.

Identifying primary/backup from the local K2 Media Server

The following procedure assumes that you are at the local K2 Media Server and you need to check
its status in its role of media file system/metadata server, especially regarding redundancy. The
recommended mode for local operation of a K2 Media Server is to use a connected keyboard,
monitor, and mouse. You can also use Windows Remote Desktop Connection from a
network-connected PC to access the Windows desktop for “local” operation, but this is not
recommended if the system is currently online with media access underway. The additional load
on network and local system resources could cause unpredictable results.

1. If you have not already done so, connect keyboard, monitor, and mouse to the K2 Media Server

and log on to Windows.

2. If Server Control Panel is not already open, on the Windows desktop, click

Start | Grass Valley

| Server Control Panel

.

282

K2 SAN Installation and Service Manual

02 February 2012

Administering and maintaining the K2 SAN

«
...
280
281
282
283
284
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: WALKMAN Страницы: 6

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: APsystems Страницы: 24

Бренд: Lenze Страницы: 28

Бренд: Manhattan Страницы: 2

Бренд: APsystems Страницы: 22

Бренд: Korenix Страницы: 2

Бренд: OTS Страницы: 3

Бренд: Lindy Страницы: 14

Бренд: REFU Страницы: 140

Бренд: Pixelfly Страницы: 12

Бренд: Cross Technologies Страницы: 18

Бренд: CYP Страницы: 23

Multi-Decoder MD-2

Бренд: tams elektronik Страницы: 40

Бренд: Hyundai Страницы: 35

Бренд: Emergi-Lite Страницы: 12

STEADYPRES M/M 11

Бренд: DGFLOW Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды