GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 366

background image

Configure Network Configuration page - K2 client

This page configures both control and media (iSCSI) network connections.

The K2 client actually has four Gigabit Ethernet ports, but two ports are configured as a teamed
pair (the control team), while the other two ports (the media connections) are individual. The teamed
pair shares an IP address and appears on this page as a single port.

1. Verify that the top port is configured correctly.

The top port is the port over which the K2Config application is communicating. If correctly
configured, it is already assigned the control network IP address, as displayed on this page.

2. Select

Media Connection #1

and then click

Modify

.

A network configuration dialog box opens.

3. Verify or configure Media Connection #1 as follows:

•

If a basic (non-redundant) K2 SAN, verify or enter the media network IP address. Also enter
the subnet mask.

•

If a redundant K2 SAN, verify or enter an IP address for the “A” media (iSCSI) network.
Also enter the subnet mask.

4. Do one of the following:

•

If a basic (non-redundant) K2 SAN, skip to the last step in this procedure. Do not configure
Media Connection #2.

•

If a redundant K2 SAN, proceed with the next step and configure Media Connection #2.

5. Select

Media Connection #2

and then click

Modify

.

A network configuration dialog box opens.

236

K2 SAN Installation and Service Manual

02 February 2012

Configuring clients on the K2 SAN

«
...
234
235
236
237
238
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

Бренд: Cablematic Страницы: 2

Бренд: Cobra Страницы: 11

Бренд: B&B Electronics Страницы: 2

Бренд: Patton electronics Страницы: 10

Бренд: X-Micro Страницы: 84

Бренд: Xnexus Страницы: 20

Бренд: B PLUS TV Страницы: 10

HYT-10.0HV-EUG1

Бренд: Hoymiles Страницы: 34

Бренд: DX Engineering Страницы: 4

Бренд: Axis Страницы: 40

PerfectPower PP150

Бренд: Waeco Страницы: 44

Бренд: M-Audio Страницы: 8

Бренд: SHOWTEC Страницы: 16

Бренд: Extron electronics Страницы: 54

Бренд: MRC Страницы: 6

maintenance and

Бренд: Dometic Страницы: 28

Box Office BOX-LNU2UXS

Бренд: Macpower & Tytech Страницы: 41

Бренд: Escient Страницы: 369

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды