GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 187

Страница: 187 / 366

2. In the K2Config application tree view, under the K2 Media Server select the File System Server

node.

The File System Server Configuration page appears.

3. Click

Check

and verify that the V: drive is shared.

Next, configure K2 clients and/or other iSCSI clients on the K2 SAN.

Configuring the basic nearline K2 SAN

Work through the topics in this section sequentially to configure a non-redundant nearline (Tier 3)
K2 SAN.

Prerequisites for initial configuration - Basic nearline K2 SAN

Before beginning your initial configuration, make sure the devices of the K2 SAN meet the following
prerequisites.

Control point PC

•

Ethernet cable connected

•

Control Point software installed

•

Control network IP address assigned

•

Network communication over the control network with all other K2 devices

•

Power on

Ethernet switch

•

Ethernet cables connected

•

Control network IP address assigned

•

VLANs set up

•

Trunks set up

•

Power on

K2 Media Server

•

Ethernet cables connected

•

Fibre Channel cable connected

•

Software installed, as from the factory, including QuickTime 7

•

Control network IP address assigned

•

Power on for all servers

K2 RAID chassis

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

02 February 2012

K2 SAN Installation and Service Manual

187

Configuring and licensing the K2 SAN

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды

GRASS VALLEY K2 BASECAMP EXPRESS, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды