GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 167

Страница: 167 / 366

•

Power on

•

Disks bound

1. If you have not already done so, launch Storage Utility from the K2Config application.

2. As prompted, wait while Storage Utility gathers system information, then Storage Utility opens.

3. In Storage Utility, click

Tools | Make New File System

The Setting dialog box opens.

4. For the Real Time Input/Output (RTIO) rate, enter the value specified by your system design.

If you do not know this value, contact your Grass Valley representative.

5. Configure Windows Security as follows:

•

If the K2 SAN is to be accessed by only K2 clients leave Windows Security unchecked.

•

If the K2 SAN is to be accessed by Aurora Edits, refer to the Aurora Edit Installation and
Configuration Guide for instructions.

02 February 2012

K2 SAN Installation and Service Manual

167

Configuring and licensing the K2 SAN

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды

GRASS VALLEY K2 BASECAMP EXPRESS, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды