GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 366

background image

Power off K2 RAID

Prerequisites for this task are as follows:

•

K2 Media Servers are powered off

1. On the primary RAID chassis controller, identify the RDY LED. It blinks at a rate of 1 blink per

second during normal operation.

Power Cords

(115V/230V)

RDY

LED

RDY

LED

Power Good

LED

Power Good

LED

2. Press and hold down the power button on a RAID controller. If you have two controllers, you

can press the power button on either RAID controller 0 or RAID controller 1.

3. Release the power button in about 5 seconds, when the RDY LED blinks more quickly, at a rate

of about 2 blinks per second. Do not hold down the power button for longer than 15 seconds.

The power button on the RAID controller turns off power for the primary RAID chassis and any
connected Expansion chassis. Power-off normally occurs within 20 seconds and is indicated
when LEDs other than those on the power supplies go off and the fans stop rotating.

4. Wait for RAID power-off to complete before proceeding.

5. Power-off all Ethernet switches.

6. Power-off the control point PC and/or the NetCentral server PC, if necessary.

Next, power off remaining SAN devices.

Power off remaining K2 SAN devices

1. Power-off all Ethernet switches.

2. Power-off the control point PC and/or the NetCentral server PC, if necessary.

The K2 SAN is powered off.

Powering on the K2 SAN

Use the following procedures to do an orderly power on of the complete K2 SAN.

02 February 2012

K2 SAN Installation and Service Manual

245

Operating the K2 SAN

«
...
243
244
245
246
247
...
»

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 BASECAMP EXPRESS

blueplanet 15.0 TL3

Бренд: Kaco Страницы: 188

Бренд: Kaiser Baas Страницы: 3

Бренд: L-Card Страницы: 73

Бренд: 3onedata Страницы: 7

Бренд: POWER ON BOARD Страницы: 13

Бренд: Xnexus Страницы: 20

Бренд: B PLUS TV Страницы: 10

Бренд: GoMax Electronics Страницы: 12

Multi-1/USB Ver4.0

Бренд: SystemBase Страницы: 63

Бренд: APT Страницы: 43

Бренд: Orgautomatech Страницы: 8

AVerCaster Combo

Бренд: Avermedia Страницы: 2

Бренд: HQ Power Страницы: 8

Бренд: Axpert Страницы: 64

Бренд: GREISINGER Страницы: 2

Бренд: Agilent Technologies Страницы: 54

Бренд: Xantrex Страницы: 112

Digital plus LE0521D

Бренд: Lenz Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды