Grandstream Networks UCM6510 Скачать руководство пользователя страница 345

Страница: 345 / 483

P a g e

344

UCM6510 IP PBX User Manual

Version 1.0.20.31

Special Extensions

Manually enter the remote extensions in the peer/register trunk to be

monitored in the event list.

Valid format: 5000,5001,9000

Event List BLF can be used to monitor remote LDAP extensions on VoIP trunks. SIP endpoints will need to

support event list BBLF to monitor remote extensions.

When an event list is created on the UCM and remote extensions are added to the list, the UCM will send

out SIP SUBSCRIBE to the remote UCM to obtain the remote extension status. When the SIP end points

list.

Once successfully configured, the event list page will show the status of total extension and subscribers for

each event list. Users can also select the event URI to check the monitored extension's status and the

subscribers' details.

--------------------------------------------------------------------------------------------------------------------------------------------

Notes:



To configure LDAP sync, please go to UCM6510 Web GUI



Extension/Trunk



VoIP Trunk

. You will

see "Sync LDAP Enable" option. Once enabled, please configure password information for the remote

peer UCM6510 to connect to the local UCM6510. Additional information such as port number, LDAP

outbound rule, LDAP Dialed Prefix will also be required. Both the local UCM6510 and remote UCM6510

need enable LDAP sync option with the same password for successful connection and synchronization.



Currently LDAP sync feature only works between two UCMs.



(Theoretically) Remote BLF monitoring will work when the remote PBX being monitored is non-

UCM6510 PBX. However, it might not work the other way around depending on whether the non-

UCM6510 PBX supports event list BLF or remote monitoring feature.

--------------------------------------------------------------------------------------------------------------------------------------------

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды