Grandstream Networks UCM6510 Скачать руководство пользователя страница 214

Страница: 214 / 483

P a g e

213

UCM6510 IP PBX User Manual

Version 1.0.20.31

"Register IAX Trunk" type is selected.

Password

Enter the password to register to the trunk from the provider when

"Register IAX Trunk" type is selected.

Disable This Trunk

If selected, the trunk will be disabled.

Table 63: IAX Register Trunk Configuration Parameters

Basic Settings

Provider Name

Configure a unique label to identify this trunk when listed in outbound rules,

inbound rules and etc.

Host Name

Configure the IP address or URL for the VoIP provider’s server of the trunk.

Keep Trunk CID

If enabled, the trunk CID will not be overridden by extension's CID when

the extension has CID configured. The default setting is "No".

Disable This Trunk

If selected, the trunk will be disabled.

Caller ID

Configure the Caller ID. This is the number that the trunk will try to use

when making outbound calls. For some providers, it might not be possible

to set the CallerID with this option and this option will be ignored.

Important Note:

When making outgoing calls, the following priority order

rule will be used to determine which CallerID will be set before sending out

the call :

From user (Register Trunk Only)



CID from inbound call (

Keep Original

CID

Enabled)



Trunk Username/CallerID (

Keep Trunk CID

Enabled)



DOD



Extension CallerID Number



Trunk Username/CallerID (

Keep

Trunk CID

Disabled)



Global Outbound CID.

CallerID Name

Configure the name of the caller to be displayed when the extension has

no CallerID Name configured.

Username

Enter the username to register to the trunk from the provider.

Password

Enter the password to register to the trunk from the provider.

Advanced Settings

Codec Preference

Select audio and video codec for the VoIP trunk. The available codecs are:

PCMU, PCMA, GSM, AAL2-G.726-32, G.726, G.722, G.729, G.723, ILBC,

ADPCM, H.264, H.265, H.263, H.263p.

Enable Heartbeat Detection

If enabled, the UCM6510 will regularly send SIP OPTIONS to the device

to check if the device is still online. The default setting is "No".

Heartbeat Frequency

When "Enable Heartbeat Detection" option is set to "Yes", configure the

interval (in seconds) of the SIP OPTIONS message sent to the device to

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды