Grandstream Networks UCM6510 Скачать руководство пользователя страница 196

Страница: 196 / 483

P a g e

195

UCM6510 IP PBX User Manual

Version 1.0.20.31

Skip Category

If enabled, the callee side will request the caller to send caller category

before sending caller number.

Note:

"Get ANI First" and "Skip Category" cannot be enabled at the same time.

Charge Calls

Whether or not report to the other end "accept call with charge". This setting

has no effect with most telecos. The default setting is enabled

(recommended).

Custom Options

Click

on “Custom Options” button (on the right top of the configuration

dialog) and then user can customize desired tone and timer options

accordingly.

Table 54: Digital Hardware Configuration Parameters: T1/J1 - PRI_NET/PRI_CPE

Basic Settings

Clock

All E1/T1/J1 spans generate a clock signal on their transmit side. The

parameter determines whether the clock signal from the far end of the

E1/T1/J1 is used as the master source of clock timing. If the far end is used

as the master, the PBX system clock will synchronize to it.



Master:

The port will never be used as a source of timing. This is

appropriate when you know the far end should always be a slave to

you.



Slave:

The equipment at the far end of the E1/T1/J1 link is the preferred

source of the master clock.

LBO

The line build-out (LBO) is the distance between the operators and the PBX.

Please use the default value 0dB unless the distance is long.

RX Gain

Configure the RX gain for the receiving channel of digital port. The valid

range is from -24dB to +12dB.

TX Gain

Configure the TX Gain for the transmitting channel of digital port. The valid

range is -24dB to +12dB.

Codec

Select alaw or ulaw. If set to default, ulaw will be used for T1/J1.

Play Local RBT

This configured whether to play the ringback tone from local UCM6510 or

not. If enabled, the local UCM6510 will play ringback tone to the caller.

Otherwise, the caller will listen to the tone from peer device. The default

setting is disabled.

Framing

Select “esf” or “d4”. Default setting is esf.

Advanced Settings

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды