Grandstream Networks UCM6510 Скачать руководство пользователя страница 200

Страница: 200 / 483

P a g e

199

UCM6510 IP PBX User Manual

Version 1.0.20.31

range is -24dB to +12dB.

Codec

Select alaw or ulaw. The default codec is ulaw for T1.

Framing

Select “esf” or “d4”. Default setting is esf.

Advanced Settings

Coding

Select B8ZS or AMI. The default setting is B8ZS for T1.

OutgoingDialDelay

The option is only valid for E&M Wink signaling. The dial delay interval after

received WINK event in an outgoing call. The default value is 200ms.

rxwink

Configure receive wink timing. The default setting is 300ms.

Digital Trunk Configuration

After configuring digital hardware, go to Web GUI



Extension/Trunk



Digital Trunks



Click on "Create New Digital Trunk" to add a new digital trunk.



Click on

to configure detailed parameters for the digital trunk.



Click on

to configure Direct Outward Dialing (DOD) for the digital Trunk.



Click on

to delete the digital trunk.

The digital trunk parameters are listed in the table below.

Table 57: Digital Trunk Configuration Parameters

Trunk Name

Configure trunk name to identify the digital trunk.

Channel Group

Configure the digital channel group used by the trunk.

Hide CallerID

Configure to hide outgoing caller ID. The default setting is "No".

Keep Trunk CID

If enabled, the trunk CID will not be overridden by extension's CID when the

extension has CID configured. The default setting is "No".

Caller ID

Configure the Caller ID. This is the number that the trunk will try to use when

making outbound calls. For some providers, it might not be possible to set

the CallerID with this option and this option will be ignored.

Important Note:

When making outgoing calls, the following priority order

rule will be used to determine which CallerID will be set before sending out

the call:

From user (Register Trunk Only)



CID from inbound call (

Keep Original

CID

Enabled)



Trunk Username/CallerID (

Keep Trunk CID

Enabled)



DOD



Extension CallerID Number



Trunk Username/CallerID (

Keep

Trunk CID

Disabled)



Global Outbound CID.

CallerID Name

Configure the new name of the caller when the extension has no CallerID

Содержание UCM6510




































































































































































































































































































































































































































































































Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды

Grandstream Networks UCM6510, Руководство пользователя

Результаты поиска

Содержание UCM6510

Отзывы:

Похожие инструкции для UCM6510

Бренды по названию

Популярные бренды