manualshive.com logo in svg

Giga-tronics 58542, Руководство по эксплуатации и техническому обслуживанию


Поделиться
Скачать
background image

58542 VXIbus Universal Power Meter

2-36

Publication 21555, Rev. E, September 2002

2.5.20

Averaging

■

SENSe:AVERage

Averaging is applied during normal operating mode. In the normal mode, Avg 

n

 results in 

n 

x 192 

samples taken. In the Swift or Burst modes, Avg 

n

 results in 2

n

 samples taken. Auto averaging takes 4 

samples all the time. For auto averaging in the normal mode, the averaging number is level dependent 
with very low averaging at +20 dBm, and many samples taken at very low levels.

SENSe:Average

Syntax:

SENSe<sensor 1 or 2>:AVERage:COUNt

space

<1,2,4,8,16,32,64,128,256,or 512>

Example:

OUTPUT @PWR_MTR;SENS1:AVER:COUN 16

! SETS SENSOR 1 AVERAGE NUMBER TO 16

Description:

This command averages successive sensor readings in a digital averaging filter. As the 
measured signal level approaches the noise floor of the power sensor, measurement data 
values begin to fluctuate. To measure very low signal levels (within a few dB of the sensor 
noise floor), set a large value for averaging such as 128, 256, or 512. Be sure to zero the 
sensor, CALibration:ZERO, prior to critical measurements.

Syntax:

SENSe<sensor 1 or 2>:AVERage:COUNt:AUTO

space

<ON | OFF>

Example:

OUTPUT @PWR_MTR;SENS2:AVER:COUN:AUTO ON  ! SELECTS SENSOR 2 AUTO-AVERAGING MODE

Description:

Auto-Averaging optimizes the measurement averaging value for reading stability and update 
rate when the measurement data is being repeatedly updated. At high power levels 
(measured), minimum averaging is applied to optimize measurement speed. As the power 
level drops, additional averaging is applied to steady the measured data reading.

Syntax:

SENSe<sensor 1 or 2>:AVERage:TCONtrol

space

<data acquisition averaging method, 

MOVing or REPeat>

Example:

OUTPUT @PWR_MTR;SENS1:AVER:TCON REP

! SETS SENSOR 1 TO ACQUIRE FRESH

! MEASUREMENT DATA BEFORE AVERAGING

Description:

The SENSe:AVERage:TCONtrol commands are instrument level commands that control the 
internal measurement data averaging of the power meter. Two modes are selectable, MOVing 
and REPeat.

The MOVing control applies the current measurement to the previously measured data. That 
is, even if the averaging number is 16, a measurement data point every time a sample is 
taken will occur, not just after every 16 samples. There is some limited built in level sensing 
capability. For example, when Auto-Averaging is used and the power is suddenly changed 
from a low value to a high, MOVing averaging throws out the very low level previous data as 
the gain range changes and begins averaging fresh data. Thus, wide abrupt changes in 
power level are not masked by the MOVing averaging. The 58542 can fully range in about      
4 ms. MOVing averaging is similar to TR1 mode in typical benchtop power meters.

REPeat averaging performs full averaging every time the 58542 is triggering. Unless the 
averaging number is set to 1, REPeat is slower than MOVing averaging. REPeat control is 
similar to TR2 mode in typical benchtop power meters. Fresh data is measured and averaged 
with each complete measurement cycle.

Содержание 58542





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 58542

Tavool MD50 User Manual preview
MD50
Бренд: Tavool Страницы: 12
VOLTCRAFT LWT-04 Operating Instructions Manual preview
LWT-04
Бренд: VOLTCRAFT Страницы: 8
Endress+Hauser Proline Promag 50H Manual preview
Proline Promag 50H
Бренд: Endress+Hauser Страницы: 52
Ofs udox Operating Instructions Manual preview
udox
Бренд: Ofs Страницы: 28
Hach DOC026.52.00769 User Manual preview
DOC026.52.00769
Бренд: Hach Страницы: 64
STM eDrometer Owner'S Manual preview
eDrometer
Бренд: STM Страницы: 31
Apera Instruments SX736 User Manual preview
SX736
Бренд: Apera Instruments Страницы: 32
wtw pH 3310 Manual preview
pH 3310
Бренд: wtw Страницы: 70
Datcon DT9500 Operating Instructions Manual preview
DT9500
Бренд: Datcon Страницы: 100
Pro'sKit MT-7029 User Manual preview
MT-7029
Бренд: Pro'sKit Страницы: 48
Mitutoyo TI-1XX User Manual preview
TI-1XX
Бренд: Mitutoyo Страницы: 2
Milwaukee MI 806 User Manual preview
MI 806
Бренд: Milwaukee Страницы: 2
Quandify CubicSecure LTCS01 User Manual & Datasheet preview
CubicSecure LTCS01
Бренд: Quandify Страницы: 11
Johnson 40-6582 Instruction Manual preview
40-6582
Бренд: Johnson Страницы: 90
Triplett RHT01 User Manual preview
RHT01
Бренд: Triplett Страницы: 2
RTI Cobia Flex R/F User Manual preview
Cobia Flex R/F
Бренд: RTI Страницы: 20
IBA ibaBM-DDCS Manual preview
ibaBM-DDCS
Бренд: IBA Страницы: 48
LaserLiner ClimaHome-Check Manual preview
ClimaHome-Check
Бренд: LaserLiner Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды