Genie GS-2669 DC Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 178

background image

Service and Repair Manual

November 2016

Fault Codes

106

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Type "PXXX" Faults, continued

DTC

Number

Message on

GCON LCD

Description

Possible Causes

Failure Mode

P032

P032:COILFAULT
BRAKE/LC LR:Bat+

Short or open circuit of the left rear
brake coil circuit.

• Short or open circuit in left rear brake harness.
• Short or open circuit in left rear brake coil.
• Left rear DCON ECM.

All functions inhibited.

P035

P035:COILFAULT
BRAKE RR:Bat-

Short circuit of the right rear coil
circuit (B5) to battery negative.

Brake circuit miswired.

• Short circuit in right rear brake harness.
• Short circuit in right rear brake coil.
• Right rear brake harness miswired.
• Right rear DCON ECM.

All functions inhibited.

P036

P036:COILFAULT
BRAKE LR:Bat-

Short circuit of the left rear brake coil
circuit (B5) to battery negative.

Brake circuit miswired.

• Short circuit in left rear brake harness.
• Short circuit in left rear brake coil.
• Left rear brake harness miswired.
• Left rear DCON ECM.

All functions inhibited.

P037

P037:BATTERY
OUT OF RANGE

Battery voltage is out of range at
startup.

• Short or open circuit in voltage sensor circuits.
• Low batteries.
• Faulty battery.
• Battery charger connected to AC power source.
• Left or right DCON ECM.

All functions inhibited.

P038

P038:DEVICEFAULT
BAT BALANCER

Battery pack out of balance.

• Short or open circuit in voltage sensor circuits.
• Faulty battery balancer.
• Faulty battery.
• Battery terminal corrosion.
• Loose battery terminal.
• GCON ECM.

All functions operate.

P039

P039:DEVICEFAULT
BRAKE PWR RELAY

Short or open circuit of the brake
relay contact or coil.

• Short or open circuit in brake relay harness.
• Brake relay contact stuck closed.
• Faulty brake relay.
• GCON ECM.

All functions inhibited.

P040

P040:COILFAULT
BRAKE PWR OPEN

Short or open circuit of the brake
relay contact or coil to battery
negative.

• Short or open circuit in brake relay harness.
• Faulty brake relay.
• Left or right DCON ECM.
• GCON ECM.

All functions inhibited.

«
...
115
116
117
118
119
...
»

Содержание GS-2669 DC



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS-2669 DC

Бренд: R&M Страницы: 53

HST 300 Print 450

Бренд: omisa Страницы: 91

Бренд: Orion Страницы: 52

Бренд: Miller Страницы: 136

Бренд: GRS Страницы: 4

Бренд: Amplicon Liveline Страницы: 42

Бренд: Elektra Beckum Страницы: 52

Fusion splicer 232103

Бренд: Televes Страницы: 24

Бренд: progressive automations Страницы: 6

Бренд: GYS Страницы: 36

Бренд: Haklift Страницы: 25

Бренд: Ravaglioli Страницы: 86

Бренд: babala Страницы: 30

Бренд: Red-D-Arc Страницы: 56

RFID-USB-DESK Reader

Бренд: inveo Страницы: 11

Бренд: Chicago Electric Страницы: 24

niagara4 MultiSITE Edge 10

Бренд: LG Страницы: 73

Бренд: Craftsman Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды