Genie GS-2669 DC Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 178

background image

Service and Repair Manual

November 2016

Scissor Components

30

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

3-5 Lift Cylinders

3-5
Lift Cylinders

The lift cylinders are single acting hydraulic
cylinders. The GS-2669 and GS-3369 uses one lift
cylinder; the GS-4069 uses two. Each lift cylinder is
equipped with a check valve to prevent movement
in the event of a hydraulic line failure.

How to Remove the Lift Cylinder

GS-2669 DC and GS-3369 DC:

Bodily injury hazard. This
procedure requires specific repair
skills, lifting equipment and a
suitable workshop. Attempting
this procedure without these skills
and tools could result in death or
serious injury and significant
component damage. Dealer
service is strongly recommended.

Note: When removing a hose assembly or fitting,
the O-ring (if equipped) on the fitting and/or hose
end must be replaced. All connections must be
torqued to specification during installation. Refer to
Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1

Remove the platform. Refer to Repair
Procedure,

How to Remove the Platform

.

2

Disassemble the scissor assembly. Refer to
Repair Procedure for your model,

How to

Disassemble the Scissor Assembly

.

GS-2669 DC and GS-3369 DC

1 solenoid valve (proportional lift models)

2 solenoid valve (2 speed lift models)

3 lift cylinder

4 pressure switch (AS/CE models)

GS-4069 DC:

Bodily injury hazard. This
procedure requires specific repair
skills, lifting equipment and a
suitable workshop. Attempting
this procedure without these skills
and tools could result in death or
serious injury and significant
component damage. Dealer
service is strongly recommended.

Note: When removing a hose assembly or fitting,
the O-ring (if equipped) on the fitting and/or hose
end must be replaced. All connections must be
torqued to specification during installation. Refer to
Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1

Remove the platform. Refer to Repair
Procedure,

How to Remove the Platform

.

«
...
39
40
41
42
43
...
»

Содержание GS-2669 DC



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS-2669 DC

Бренд: WAGO Страницы: 18

Бренд: WAGO Страницы: 46

TRANSITIONS Angled Entry Mat

Бренд: EZ-ACCESS Страницы: 4

FORCE 125 230V ACD

Бренд: Telwin Страницы: 104

FOCUS 200 AC/DC PFC

Бренд: Migatronic Страницы: 66

Бренд: ATEN Страницы: 176

Бренд: Kenco Страницы: 15

NVL Vista 05 Series

Бренд: Braun Страницы: 30

Бренд: Lincoln Electric Страницы: 15

Бренд: TBM Страницы: 21

Бренд: Pro-Lift Страницы: 20

Бренд: Haklift Страницы: 32

JFLEX-Visualisation1

Бренд: Kontron Страницы: 19

Бренд: suntouch Страницы: 20

Бренд: GammaSwiss Страницы: 32

Compact 2 Series

Бренд: DATAEAGLE Страницы: 2

fantech VHR 200R

Бренд: SystemAir Страницы: 44

Бренд: Buderus Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды