Genie GS-2669 DC Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 178

background image

Service and Repair Manual

November 2016

Outrigger Components

84

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Outrigg er Co mpon ents

10- 1 O utri gger Cyli nder

10-1
Outrigger Cylinder

How to Remove an Outrigger
Cylinder (if equipped)

Note: When removing a hose assembly or fitting,
the O-ring (if equipped) on the fitting and/or hose
end must be replaced. All connections must be
torqued to specification during installation. Refer to
Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1

Remove the mounting fasteners from the
inside outrigger cylinder cover. Remove the
cover.

2

Remove the outrigger hose cover.

3

Disconnect the outrigger limit switch and
cylinder valve connectors.

4

Remove the mounting fasteners from the
outside outrigger cover. Remove the cover.

5

Tag, disconnect and plug the hydraulic hoses
from the outrigger cylinder. Cap the fittings on
the cylinder.

Bodily injury hazard. Spraying
hydraulic oil can penetrate and
burn skin. Loosen hydraulic
connections very slowly to allow
the oil pressure to dissipate
gradually. Do not allow oil to
squirt or spray.

6

Attach a lifting strap from an overhead crane
to the barrel end of the outrigger cylinder for
support. Do not apply any lifting pressure.

7

Remove the outrigger mounting fasteners.
Slide the outrigger cylinder down and away
from the machine.

Crushing hazard. The outrigger
cylinder may become
unbalanced and fall if not
properly supported when
removed from the machine.

Note: If the outrigger cylinder is being replaced,
remove the foot pad assembly and install it on the
replacement cylinder.

Note: After an outrigger cylinder has been installed,
the machine must be re-calibrated. Refer to Repair
Procedure,

Outrigger Calibration

.

«
...
93
94
95
96
97
...
»

Содержание GS-2669 DC



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS-2669 DC

Бренд: U-Line Страницы: 7

Бренд: Harmar Mobility Страницы: 53

Бренд: Lathem Страницы: 4

KPH 370.70 LIKT

Бренд: rav Страницы: 82

Бренд: Grundfos Страницы: 27

Maxstar 150 STL

Бренд: Miller Electric Страницы: 4

Бренд: gala gar Страницы: 42

PIO-32/32RL(PCI)H

Бренд: Contec Страницы: 4

Бренд: Happ Страницы: 42

Бренд: Migatronic Страницы: 94

Fusion splicer 232103

Бренд: Televes Страницы: 24

Бренд: Balluff Страницы: 42

Бренд: Noblelift Страницы: 6

Бренд: i4Technology Страницы: 6

Бренд: Pro Spot Страницы: 44

Бренд: Elettro CF Страницы: 38

Invertig 221 AC/DC

Бренд: HTP Страницы: 28

Бренд: Brewolution Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды