Genie GS-2669 DC Скачать руководство пользователя страница 102

Страница: 102 / 178

November 2016

Service and Repair Manual

Platform Overload Components

Part No. 1272220GT

GS-2669 DC • GS-3369 DC • GS-4069 DC

11- 2 Plat form Ov erload R ec ov ery

11-2
Platform Overload Recovery
Message

If the ground controls LCD screen displays

OL:

PLATFORM OVERLOADED

, the emergency

lowering system has been used while the platform
was overloaded.

How to Clear the Platform
Overload Recovery Message

Note: This message shall be cleared by a person
trained and qualified on the troubleshooting and
repair of this machine.

Note: Use the following chart to identify the
description of each LCD screen control button used
in this procedure.

Escape

Scroll up

Scroll down

Enter

Turn the key switch to the ground controls
position and pull out the red Emergency Stop
button to the on position at the platform
controls.

Press and hold the ground control

scroll up

and

scroll down

buttons.

Pull out the red Emergency Stop button at the
ground controls.

Result: The ground control LCD display will
show the following.

Press the

scroll down

button.

Result: The ground control LCD display will
show the following.

Press the

enter

button.

Result: The ground control LCD display will
show the following.

Press the

enter

button.

Result: The ground control LCD display will
show the following.

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды