Genie GS-2669 DC Скачать руководство пользователя страница 123

Страница: 123 / 178

Service and Repair Manual

November 2016

Fault Codes

112

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Type "CXXX" Faults

Type "CXXX" Faults

DTC

Number

Message on

GCON LCD

Description

Possible Causes

Failure Mode

C001

C001:GCON ECM
FAULT TYPE 1

GCON ECM CRC check error.

• Incorrect software file.
• GCON ECM internal failure.

All functions inhibited.

C004

C004:GCON ECM
FAULT TYPE 4

GCON ECM master switch error.

• Short circuit in the master switch circuit.
• GCON ECM.

All functions inhibited.

C005

C005:GCON ECM
FAULT TYPE 5

GCON ECM safety switch error.

• Short circuit in the safety switch circuit.
• GCON ECM.

All functions inhibited.

C006

C006:GCON ECM
FAULT TYPE 6

GCON input redundancy error.

• Input conditioning circuit failure.
• GCON ECM.

All functions inhibited.

C007

C007:GCON ECM
FAULT TYPE 7

GCON ECM inter-processor
communication error.

• Incorrectly programmed device.
• Error in loading software on device.
• GCON ECM.

All functions inhibited.

C008

C008:GCON ECM
FAULT TYPE 8

GCON ECM temperature sensor
error.

• GCON ECM internal failure.
• GCON ECM.

All functions operate.

C009

C009:GCON ECM
FAULT TYPE 9

GCON fault type 9.

• Contact Genie support.

C010

C010:SECONDARY
NOT PROGRAMMED

Secondary not programmed.

• Reinstall software
• Contact Genie support.

All functions inhibited.

C021

C021:PCON NOT
DETECTED

Communication failure between
GCON and PCON.

• CAN communication failure.
• CAN communication harness.
• PCON disconnected.
• GCON or PCON ECM.

All functions inhibited.

C023

C023:MACHINE
MODEL FAULT

Discrepancy between model
detected and model programmed.

• Incorrect machine model programmed.
• GCON or PCON ECM.

All functions inhibited.

C025

C025:SYSTEMFAULT
PLAT OVLD:NOCAL

Platform overload system not
calibrated.

• Platform overload system not calibrated.
• GCON or PCON ECM.

All functions inhibited.

C028

C028:SERVICE
OVERRIDE MODE ON

Machine is in service override mode. • Machine programmed for use in service override mode.

All functions inhibited
except for down function
and up function.

Platform can be elevated
only once with the
maximum elevate time of
XX seconds.

Elevate time XX depends
on machine model.

C029

C029:SYSTEMFAULT
OUTRIGGER:NoCal

Outrigger fault, not calibrated.

• Calibrate outriggers
• Contact Genie support.

All functions operate. Will
not lift above the down
limit switches.

C030

C030:DCON RR ECM
FAULT TYPE 01

Hardware failure of the right rear
drive controller.

• Right rear DCON ECM.

Performance reduced or
all functions inhibited.

C031

C031:DCON LR ECM
FAULT TYPE 01

Hardware failure of the left rear drive
controller.

• Left rear DCON ECM.

Performance reduced or
all functions inhibited.

C032

C032:DCON RR ECM
FAULT TYPE 02

Setup initialization failure of the right
rear drive controller at system
startup.

• Drive input active at system startup.
• Faulty drive joystick.
• Incorrect software.D14
• Right rear DCON ECM.

Performance reduced or
drive inhibited or all
functions inhibited.

C033

C033:DCON LR ECM
FAULT TYPE 02

Setup initialization failure of the left
rear drive controller at system
startup.

• Drive input active at system startup.
• Faulty drive joystick.
• Incorrect software.D14
• Left rear DCON ECM.

Performance reduced or
drive inhibited or all
functions inhibited.

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды