Genie GS-2669 DC Скачать руководство пользователя страница 43

Страница: 43 / 178

Service and Repair Manual

November 2016

Ground Controls

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Ground C ontrol s

Ground Controls

The ground controls, used to operate the machine
from the ground, can also be used to tune the
performance of the machine.

The ground controls consist of an Electronic
Control Module (ECM), emergency stop button,
key switch and circuit breaker.

Activating the function enable button and the up or
down at the same time, sends a signal to the
(ECM). This allows the platform to be raised or
lowered at the ground controls.

Note: Steer and drive functions are not available at
the ground controls.

When the ECM is in the set up mode, the ground
controls are used to adjust the function speed
parameters, machine models, or machine options.

For further information or assistance, contact
Genie Product Support.

1 machine setup, escape button

2 machine setup, scroll up button

3 LCD display

4 machine setup, scroll down button

5 machine setup, enter button

6 key switch KS1

7 red Emergency Stop P1

8 engine start

9 ECM U1

10 platform down button

11 lift function enable button

12 platform up button

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды